75.140 (Waxes, bituminous materials and other petr 标准查询与下载

ASTM D2319/D2319M-98(2008)e1 沥青软化点的标准试验方法(空气中立方块试验方法)

Pitch does not go through a solid-liquid phase change when heated and therefore does not have a true melting point. As the temperature is raised, pitch softens and becomes less viscous. The softening point is arbitrarily defined and must be determined by a closely controlled method that must be carefully followed if test results are to be reproducible. This test method is useful in determining the consistency of pitch as one element in establishing the uniformity of shipments and sources of supply.1.1 This test method covers the determination of the softening point above 80°C [176°F] of pitch. Test Method D 3104 gives comparable results. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Softening Point of Pitch (Cube-in-Air Method)

ASTM D2320-98(2008) 固态沥青密度(相对密度)的标准试验方法(比重瓶法)

Values of density and relative density are used for converting volumes to units of mass as required in other ASTM standards and in sales transactions.1.1 This test method covers the determination of density and relative density by pycnometer, and can be used for pitch that can be handled in fragments. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Density (Relative Density) of Solid Pitch (Pycnometer Method)

ASTM D2319-98(2003) 硬沥青软化点的标准试验方法(空气中立方块试验法)

Pitch does not go through a solid-liquid phase change when heated and therefore does not have a true melting point. As the temperature is raised, pitch softens and becomes less viscous. The softening point is arbitrarily defined and must be determined by a closely controlled method that must be carefully followed if test results are to be reproducible. This test method is useful in determining the consistency of pitch as one element in establishing the uniformity of shipments and sources of supply.1.1 This test method covers the determination of the softening point above 176176;F (80176;C) of pitch. Test Method D 3104 gives comparable results.1.2 The values stated in SI units are to be regarded as the standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Softening Point of Pitch (Cube-in-Air Method)

ASTM D2320-98(2012) 固态沥青密度(相对密度)的标准试验方法(比重瓶法)

1.1 This test method covers the determination of density and relative density by pycnometer, and can be used for pitch that can be handled in fragments. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Density (Relative Density) of Solid Pitch (Pycnometer Method)

ASTM D2415-98(2012) 煤焦油和沥青中灰分的标准试验方法

1.1 This test method covers the determination of the ash content of tar and pitch. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Ash in Coal Tar and Pitch

ASTM D4715-98(2012) 焦油和硬沥青焦化值测定的标准试验方法(Alcan)

1.1 This test method covers the determination of the coking value of tar and pitch having an ash content not over 0.58201;%, as determined by Test Method D2415. 1.2 Coking values by this test method are higher than those obtained by Test Method D2416. See the bias statement in Section 13. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Coking Value of Tar and Pitch (Alcan)

ASTM D2318-98(2003) 焦油和硬沥青中喹啉不溶物(QI)含量的标准试验方法

This test method is useful in evaluating and characterizing tar and pitch, and as one element in establishing the uniformity of shipments and sources of supply.1.1 This test method covers the determination of the quinoline-insoluble matter (QI) in tar and pitch.1.2 Since this test method is empirical, strict adherence to all details of the procedure is necessary.1.3 The values stated in SI units are to be regarded as the standard.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. See Section .

Standard Test Method for Quinoline-Insoluble (QI) Content of Tar and Pitch

ASTM D4715-98 测定焦油和硬沥青焦化值的试验方法(Alcan)

1.1 This test method covers the determination of the coking value of tar and pitch having an ash content not over 0.5%, as determined by Test Method D2415. 1.2 Coking values by this test method are higher than those obtained by Test Method D 2416. See the bias statement in Section 13. 1.3 The values stated in inch-pound units are to be regarded as the standard. 1.4 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Coking Value of Tar and Pitch (Alcan)

ASTM D2318-98(2013) 焦油和硬沥青中喹啉不溶物(QI)含量的标准试验方法

4.1 This test method is useful in evaluating and characterizing tar and pitch, and as one element in establishing the uniformity of shipments and sources of supply. 1.1 This test method covers the determination of the quinoline-insoluble matter (QI) in tar and pitch. 1.2 Since this test method is empirical, strict adherence to all details of the procedure is necessary. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For hazards information, see Section 7.

Standard Test Method for Quinoline-Insoluble (QI) Content of Tar and Pitch

ASTM D2319/D2319M-98(2013) 沥青软化点的标准试验方法(空气中立方块试验方法)

4.1 Pitch does not go through a solid-liquid phase change when heated and therefore does not have a true melting point. As the temperature is raised, pitch softens and becomes less viscous. The softening point is arbitrarily defined and must be determined by a closely controlled method that must be carefully followed if test results are to be reproducible. 4.2 This test method is useful in determining the consistency of pitch as one element in establishing the uniformity of shipments and sources of supply. 1.1 This test method covers the determination of the softening point above 80°C [176°F] of pitch. Test Method D3104 gives comparable results. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Softening Point of Pitch (Cube-in-Air Method)

ASTM D4072-98(2013) 测定焦油和硬沥青中甲苯不溶物质(TI)含量的标准试验方法

4.1 This test method is useful for evaluating and characterizing tars and pitches and as one element in establishing the uniformity of shipments or sources of supply. 1.1 This test method covers the determination of toluene-insoluble matter (TI) in tar and pitch. 1.2 Since this test method is empirical, strict adherence to all details of the procedure is necessary. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard information, see Section 7.

Standard Test Method for Toluene-Insoluble (TI) Content of Tar and Pitch

ASTM D4715-98(2003) 测定焦油和硬沥青焦化值的试验方法(Alcan)

This test method is useful for indicating the relative coke-forming propensities and for evaluating and characterizing tars and pitches. The test method can also be used as one element in establishing the uniformity of shipments or sources of supply.1.1 This test method covers the determination of the coking value of tar and pitch having an ash content not over 0.5 %, as determined by Test Method D 2415.1.2 Coking values by this test method are higher than those obtained by Test Method D 2416. See the bias statement in Section .1.3 The values stated in inch-pound units are to be regarded as the standard.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Coking Value of Tar and Pitch (Alcan)

ASTM D937-97(2002) 石油脂的针入度试验方法

1.1 This test method covers measuring with a penetrometer the penetration of petrolatum as an empirical measure of consistency.1.2 The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Cone Penetration of Petrolatum

ASTM D6135-97 自黏改良沥青防水应用的标准操作规程

1.1 This practice covers the minimum installation recommendations for self-adhering modified bitumen sheets used in waterproofing. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Application of Self-Adhering Modified Bituminous Waterproofing

ASTM D5515-97(2010) 用膨胀计测定烟煤膨胀特性的标准试验方法

Values of the dilatation properties of coals may be used to predict or explain the behavior of a coal or blends during carbonization or in other processes such as gasification, liquefaction, and combustion.1.1 This test method specifies a procedure for the measurement of the swelling of bituminous coal using a dilatometer. 1.2 The test method is limited in applicability to those coals which have a free swelling index ≥1 as determined in accordance with Test Method D720. 1.3 The values stated in SI units () are to be regarded as standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Determination of the Swelling Properties of Bituminous Coal Using a Dilatometer

ASTM D5515-97(2004)e2 用膨胀计测定烟煤膨胀特性的标准试验方法

1.1 This test method specifies a procedure for the measurement of the swelling of bituminous coal using a dilatometer. 1.2 The test method is limited in applicability to those coals which have a free swelling index 1 as determined in accordance with Test Method D 720.1.3 The values stated in SI units (IEEE/ASTM SI-10) are to be regarded as standard.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Determination of the Swelling Properties of Bituminous Coal Using a Dilatometer

ASTM D3235-97 石油蜡中溶剂可淬取性的试验方法

1.1 This test method covers the determination of solvent extractables in petroleum waxes. 1.2 The values stated in acceptable metric units are to be regarded as the standard. The values in parentheses are for information only. 1.3 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Solvent Extractables in Petroleum Waxes

ASTM D721-97 石油蜡含油量的试验方法

1.1 This test method covers the determination of oil in petroleum waxes having a congealing point of 30176C (86176F) or higher as determined in accordance with Test Method D938, and containing not more than 15 % of oil. 1.2 The values stated in inch-pound units are to be regarded as the standard. The values in parentheses are for information only. Note 1-With some types of waxes, of oil contents greater than 5 %, there may be an incompatibility with MEK resulting in the formation of two liquid phases. If this occurs, the method is not applicable to the material under test. 1.3 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Oil Content of Petroleum Waxes

ASTM D5515-97 用膨胀计测定烟煤膨胀特性的标准试验方法

1.1 This test method specifies a procedure for the measurement of the swelling of bituminous coal using a dilatometer. 1.2 The test method is limited in applicability to those coals which have a free swelling index [>=] 1 as determined in accordance with Test Method D720. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.4 The values stated in SI units (Practice E380) are to be regarded as standard.

Standard Test Method for Determination of the Swelling Properties of Bituminous Coal Using a Dilatometer

ASTM D1321-97 石油蜡针入度的试验方法

1.1 This test method covers the empirical estimation of the consistency of waxes derived from petroleum by measurement of the extent of penetration of a standard needle. This test method is applicable to waxes having a penetration of not greater than 250. Note 1-This test method is similar to the needle method for determining the penetration of bituminous material, Test Method D5. Cone methods applicable to greases and to petrolatum are described in Test Methods D217 and Test Method D937, respectively. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Needle Penetration of Petroleum Waxes